FAQ · Charlotte, NC
Commercial Door Questions from Charlotte Businesses
These are the questions Charlotte businesses ask most about their commercial doors, gathered in one place. General questions come first, then the most common questions for each service, with a link to the full page.
Call with a door question(984) 367-2696Calls only. No forms on this site.
General
General questions
Do you only serve Charlotte?
Yes. This service covers businesses in Charlotte, North Carolina only, from Uptown and South End to University City, Steele Creek and Ballantyne. One city keeps the focus where it belongs.
What commercial doors do you work on?
Aluminum storefront and glass entrances, automatic sliding and swing doors, push-button ADA openers, closers, pivots and hinges, panic bars and exit devices, commercial locks, hollow metal steel doors and frames, fire-rated doors, and overhead, dock and roll-up doors.
Why is there no contact form?
A door problem is quicker to sort out on the phone. Two minutes of questions about the door, the hardware and whether the building is secure gets you a straight answer faster than an email.
Can you give me a price over the phone?
You can get an honest idea of what is involved and what drives the cost. A firm price depends on seeing the door, because the part that failed often has a cause behind it.
Do you install new doors as well as repair them?
Yes. When a door is past repair, a replacement is fitted, usually on the existing frame, along with the closer, lock and exit hardware it needs.
Do you repair fire doors that failed inspection?
Yes. Fire door deficiencies are repaired with parts that keep the rating, and you get a door-by-door record of the work.
What should I have ready when I call?
The address in Charlotte, the door type, what it is doing, when it started and whether the building can be secured. A brand name on the closer, lock or operator helps.
By service
Storefront and entrance systems
Storefront Door Repair in Charlotte
Can a dragging storefront door be fixed without replacing it?
Usually, yes. Dragging is most often a worn pivot or a loose corner joint letting the latch side drop. Replacing the pivot and squaring the door fixes the cause.
Why does my storefront door only lock if I push it?
The door has dropped or shifted, so the lock bolt no longer lines up with the strike. Moving the strike hides the problem; rehanging the door fixes it.
Automatic Door Repair in Charlotte
My automatic door keeps closing on people. What should I do?
Switch it to open or off if it has a mode switch, or lock it open safely, and keep people clear of the panels. Then call. A door that does not detect people is a safety fault and should not keep running.
Can you repair any brand of automatic door?
Most commercial automatic door operators can be repaired with standard sensors, belts and carriers. Tell us the brand on the header when you call so the right parts can be checked.
ADA Door Opener Installation in Charlotte
Is my business required to have an automatic door opener?
The ADA does not generally require automatic openers, but it does limit how hard doors are to open and how fast they close. When a door cannot meet those limits, an opener is a common solution. Your architect or code official has the final word for your building.
Can an opener go on my existing door?
Usually, yes. Most aluminum storefront, hollow metal and wood doors take a surface-mounted low-energy operator, provided the door swings freely and the frame is sound.
Commercial Door Closer Repair in Charlotte
Can a slamming door closer be adjusted?
Usually, if it is not leaking. Closing speed and latch speed are set with separate valves. If the closer is leaking oil, adjustment will not last and it should be replaced.
Why does my door closer leak oil?
Its internal seals have failed. Once a closer leaks it loses control of the door and cannot be adjusted back. Replacement is the fix.
Door Pivot and Hinge Repair in Charlotte
Why is my commercial door sagging?
Almost always worn pivots or hinges, or hinge screws pulling out of the frame. The door drops at the latch side, then drags and stops latching.
Are pivots and hinges interchangeable?
Not directly. A door hung on pivots is prepared differently from one hung on hinges. Some doors can be converted to a continuous hinge, which carries the weight along the full height.
By service
Exit hardware, locks and steel doors
Panic Bar and Exit Device Repair in Charlotte
Is a stuck panic bar an emergency?
Yes. If an exit door does not open with one push from inside, people may not be able to get out. Keep another exit available and call.
Why does my panic bar door not latch?
Usually the latch or rod is out of adjustment, or the door has dropped so the latch misses the strike. On vertical rod devices, debris in the floor strike is a common cause.
Commercial Door Lock Repair in Charlotte
My storefront door will not lock. What is wrong?
Usually the door has dropped so the bolt misses the strike, or the cylinder is worn. Try the lock with the door held exactly closed; if it works then, the door needs rehanging.
What is the difference between rekeying and replacing a lock?
Rekeying changes the cylinder so old keys stop working. Replacing changes the lock itself. Rekeying is enough when the lock still works and you only need new keys.
Hollow Metal Door Repair in Charlotte
Can a rusted steel door be repaired?
Light surface rust can be treated and painted. If the bottom of the door has rusted through, a new door fitted to the existing frame is usually the better repair.
Do I need to replace the frame too?
Usually not. Frames can often be re-anchored, straightened and kept, which avoids cutting into the wall.
Fire Door Repair in Charlotte
How often do fire doors need to be inspected?
NFPA 80 calls for fire door assemblies to be inspected and tested at least once a year, with records kept. Your fire marshal or insurer may add requirements of their own.
Can you fix the doors on our inspection report?
Yes. Go through the deficiency list on the call. Each door is repaired with listed parts and you get a door-by-door record of the work.
By service
Overhead doors, installation and emergencies
Commercial Overhead Door Repair in Charlotte
Can I open my overhead door with a broken spring?
No. Leave it where it is, unplug or lock out the opener and keep people clear. The door can weigh hundreds of pounds and may drop without warning.
Do you repair roll-up doors as well as sectional doors?
Yes. Rolling steel doors and grilles, and sectional dock and service-bay doors, are all covered.
Commercial Door Installation in Charlotte
Can you replace a door without replacing the frame?
Usually, yes, if the frame is sound. The new door is prepared to match the existing hinge or pivot, lock and closer locations.
How long does a new commercial door take?
Stock hollow metal and storefront doors can be quick. Made-to-order sizes, finishes and fire-rated doors take longer, and the opening is kept secure meanwhile.
Emergency Commercial Door Repair in Charlotte
What if it happens after hours?
Call as soon as it happens and say it is an emergency. You will be told straight away whether, and how soon, someone can come.
My storefront glass was smashed. What should I do?
Keep people clear of the glass, take photos for your insurer, and call. The opening is made secure first, then the glass is replaced.
Commercial Door Questions from Charlotte Businesses
Commercial doors in Charlotte, NC. One call is all it takes.