Charlotte, NC only · Commercial doors · Phone only, no formsCall (984) 367-2696
Commercial Doors Charlotte: storefront and entrance systems Commercial doors, Charlotte(984) 367-2696

Charlotte, NC · Pivots & hinges

Door Pivot and Hinge Repair in Charlotte

When a commercial door sags, drags or hangs crooked in its frame, the pivots or hinges carrying its weight are usually worn or torn loose. We repair and replace offset pivots, center pivots, continuous hinges and heavy-duty butt hinges on storefront, steel and wood doors across Charlotte.

Call about pivots & hinges(984) 367-2696

Urgent The door moves up and down, or a hinge has torn loose

Signs

What the door is doing, and what that usually means

Door Pivot and Hinge Repair in Charlotte: signs, likely causes and urgency
What you seeWhat it usually meansHow urgent
Latch side of the door dragsA worn top or bottom pivot, or loose hinge screwsToday
Uneven gap at the top cornerThe door has dropped on its pivots or hingesThis week
Squeaking or grinding as it swingsA dry or worn pivot bearing or hinge knuckleSchedule
Hinge screws pulled out of the frameDoor weight and slamming have stripped the frameToday
Door feels loose or moves up and downA failed pivot; the door can drop out of its frameUrgent

Urgent People are at risk, an exit will not work, or the building cannot be secured. Today The door is failing at its job and every cycle makes it worse. This week Still working, but the wear is visible. Fixing it now costs less than fixing it after it fails. Schedule Not urgent. Worth planning into the next visit.

What gets checked

The inspection

The part named on the call is rarely the only one involved. These are checked on every door pivot and hinge repair visit in Charlotte:

  • Top pivot Bearing wear and the pivot fixings in the head of the frame.
  • Bottom pivot Wear, corrosion and whether the door still sits on its spindle.
  • Hinge knuckles and leaves Wear, bent leaves and gaps that let the door drop.
  • Screws and reinforcement Stripped holes, missing screws and whether the frame has hinge reinforcement.
  • Door squareness Whether the stiles and corners have racked from the sag.
  • Clearances Even gaps at the head, latch side and threshold after the repair.
Technician in a white hard hat and safety glasses holding a yellow spirit level against the aluminum frame of a glass storefront
Checking an aluminum storefront frame for plumb. A door can only hang true in a frame that is square.

The repair

How door pivot and hinge repair is done

  1. Support the door and measure how far it has dropped.

  2. Remove the worn pivot or hinge and check the frame and door fixings behind it.

  3. Fit matching hardware, adding reinforcement where screws have stripped.

  4. Rehang the door square, then check closer, latch and lock alignment.

Why pivots and hinges wear out

A commercial door can weigh well over a hundred pounds, and on a busy entrance it swings hundreds of times a day. All of that weight hangs on two pivots or a few hinges. When a top pivot wears or a hinge screw strips, the door drops a little at the latch side, and every swing after that makes it worse. Continuous gear hinges spread the load along the full height of the door, which is why they are a common upgrade on hard-working doors.

Pivots on storefront doors

Aluminum storefront doors usually hang on offset pivots at the top and bottom, and many have an intermediate pivot as well. Pivots are made to be replaced, and the correct part restores the door's original fit. Floor closers under glass doors act as the bottom pivot, so they are checked as part of the same job.

Straight answers

Repair or replace?

Usually repairable

  • Worn pivots and hinges, replaced with matching hardware
  • Stripped screw holes re-tapped or reinforced
  • Doors rehung and squared in the frame

Replacement makes sense

  • Frames torn or cracked where the hinges mount
  • Doors racked so badly the corners will not stay tight
  • Obsolete hardware with no compatible replacement

Have this ready when you call

  • Pivots or hinges, if you know
  • Door material, and whether it is a single or a pair
  • Which side drags, or where the gap opened
  • Whether the door still locks
Call about pivots & hinges(984) 367-2696

In Charlotte

Pivots & hinges in Charlotte buildings

In Charlotte, worn pivots show up most on busy retail and restaurant entrances in South End, SouthPark and University City, and on older storefronts in NoDa and Plaza Midwood where the original hardware has carried decades of traffic. Steel back doors behind restaurants and warehouses tend to strip their hinge screws first.

FAQ

Door Pivot and Hinge Repair: common questions

Why is my commercial door sagging?

Almost always worn pivots or hinges, or hinge screws pulling out of the frame. The door drops at the latch side, then drags and stops latching.

Are pivots and hinges interchangeable?

Not directly. A door hung on pivots is prepared differently from one hung on hinges. Some doors can be converted to a continuous hinge, which carries the weight along the full height.

What is a continuous hinge?

A full-height hinge that spreads the door's weight over its whole edge. It is a common upgrade for heavy or very busy doors that keep wearing out pivots or butt hinges.

Can a sagging door be fixed by adjusting it?

Only if the hardware is still sound. If a pivot is worn or a hinge screw is stripped, the door will sag again until the hardware is replaced.

Door Pivot and Hinge Repair in Charlotte

Sagging, dragging or hanging crooked. Call and describe the door.

Call about pivots & hinges(984) 367-2696
Call (984) 367-2696